ANTC-V2.2 series
Anemometer cups with multiple outputs for industry-standard ACCREDIA certificate
ANTC-V2.2 is an anemometer, which meets every requirement of use in electronics. Is in fact equipped with its own programmable logic and, thanks to a large range of power supply, from 10 to 30Vdc, can be used for any on-board detection of wind turbines in the presence of sources of power from batteries 12 and 24 vdc vdc.
Its output signal can be configured for pulse output, voltage output 0-5 / 1-5 / 0-10 / 2-10 Vdc, current output 0-20 / 4-20 mA.
Applications
The Anemometer ANTC-V2.2 has been specifically designed for industrial applications such as:
- Cranes and Mobile Cranes
- Buildings and general structures
- Photovoltaic solar trackers
- Wind turbines
- Weather Stations
- Irrigation systems
- Automated greenhouses
- Cable cars for ski plants
- Cannons snow
- Telescopic cranes
- Platforms self-mounting
- Structures for playgrounds
- Ornamental fountains
- Pressostatic structures
- Highway tunnels and viaducts
The body of the rotor is machined aluminum. The head rotates on ball bearings. The cups are made of nylon shock-absorbent and easily interchangeable.
It 'also features a convenient connector for connection.
The count rate is via optical transducer, a digital encoder with 12 pulses per revolution.
Each transducer is tested in a wind tunnel and equipped with a calibration certificateRuns on request, a periodic calibration on products.
Other Applications
The body of the rotor is machined aluminum. The head rotates on ball bearings. The cups are made of nylon shock-absorbent and easily interchangeable.
It 'also features a convenient connector for connection. The count rate is via optical transducer, a digital encoder with 12 pulses per revolution.
Each transducer is tested in a wind tunnel and equipped with a calibration certificate
Runs on request, a periodic calibration on products.
- Technical Features
- Standards
- Surveys
- Accessories
- Optional Items
- Download
Main Features
- Robust, reliable, suitable for heavy duty industrial use in extreme conditions
- Range of use 2-200km/h
- Stainless-steel ball bearings
- Body in anodized alluminium
- Jack connector
- Stainless steel support
Mechanical Features
The anemometer consists of aluminium body and rotor with a removable hat for the mechanical seal of a Nylon Cups shockproof, UV ray, low temperature and hailstorm resistant. Rotating on a Ball Bearings, moves a cogwheel that through a photodiode gives 12 pulses per 1 rotation.
- IP66 degree protection
- Operating temperature -20° + 85°C
- Stock temperature -40° + 125°C
- Overall size on a side draw
- Weight 300 g connection cable excluded
- Measurement range from 2 to 200 km/h
- Medium error 0,06 %
- Standard deviation error 1,01 %
- Analisys done in a wind tunnel with a 0 to 200 m/s wind speed exceeding
Electric Features
| Items | ANTC_V2.2_Hz |
ANTC_V2.2_Vdc |
ANTC_V2.2_mA |
| Power supply | 10/30 Vdc |
10/30 Vdc |
10/30 Vdc |
| Signal output that can be configurable by manufacturer |
frequency | Voltage. Output to be configurable by manufacturer:0-5 / 1-5 / 0-10 / 2-10 Vdc | Current. Output to be configurable by manufacturer:0-20 / 4-20 mA |
| Current / consumption | 50mA | 50mA | 50mA |
| Measuring range of mechanical and electrical | 2-200Km/h |
2-200Km/h |
2-200Km/h |
| Configurable by manufacturer fullscale | 0 - 100 0 - 120 0 - 180 0 - 200 |
0 - 100 0 - 120 0 - 180 0 - 200 |
0 - 100 0 - 120 0 - 180 0 - 200 |
| Impedance maximum load | - | - | Equal or less than 500 ohm |
| Current maximum load | 10mA |
10mA |
- |
| Cable lenght pre wired | Every lenght can be requested |
Every lenght can be requested |
Every lenght can be requested |
Dimensions
-
Body rotor: H 115 mm
- Body rotor + support: H 154 mm
- Body rotor + support + connector: H 163 mm
- Diam. min. top body rotor: 29 mm
- Diam. max. bottom body rotor: 40 mm
- Diam. max. rotating head with cups assembled: 124 mm
- Stainless steel support assembled. Dimensions: H 52 mm / W 40 mm
M12 Connector
Connection jack connector welding side view:
1=0v GND 4=+12/24 Vdc 3=output signal
CAUTION: Use shielded cable 3x0,5 sq mm - the braided shield MUST NOT BE CONNECTED to the ground connector but completely isolated. It should be connected to ground only from the connection to the PLC electronics, display or electronic ANTC.
Regulations
- EN 61000-6-1:2001
- EN 55022:2001, CLASS B
Operation
ANTC-V2.2 anemometer can be configured on the following features:
- ANTC_V2.2_Hz Model
- ANTC_V2.2_Vdc Model
- ANTC_V2.2_mA Model
ANTC_V2.2_Hz model
Configurable Outputs: Frequency Output
Operation:
- Relation between Wind Speed – Frequency output.
- The output pulses are proportional to the wind speed in relation with the following graphic
ANTC_V2.2_Vdc Model
Configurable Outputs: Voltage Output
Operation:
- Relation between Wind Speed – Voltage output.
- The voltage output is proportional to the wind speed in relation with the following graphic.
- These follow are configurable sets:
- 0-5 / 1-5 / 0-10 / 2-10 Vdc
- The graph to the side is represented in function of the maximum speed configurable = 200 km / h
- Are available the follow Fullscale value:
- 200 km/h - 180 km/h - 120 km/h - 100 km/h
ANTC_V2.2_mA Model
Configurable Outputs: Current Output
Operation:
- Relation between Wind Speed – Current output.
- The current output is proportional to the wind speed in relation with the following graphic.
- These follow are configurable sets: 0-20 / 4-20 mA
- The graph to is represented in function of the maximum speed configurable = 200 km / h
Are available the follow Fullscale value:
200 km/h - 180 km/h - 120 km/h - 100 km/h
Warning: 500 ohm maximum load
Graphs:
Nylon Cups
Black cup reinforced by the hail, resistant from -40°C to +120°C, diam. 30mm, interchangeable.
The kit includes 3 cups.
M12 Connector
M12 Connector
- PIN 1 | O Vdc
- PIN 3 | SIGNAL
- PIN 4 | +10/30Vdc
Stainless-steel Bracket
AISI 316 STAINLESS STEEL version
Heater Version
Complete of anti-icing HEATER.
ALSO STAINLESS STEEL VERSION
Connecting Cable
